X7+ Pro AutoPilot


X7+ Pro® is an advanced autopilot independently designed by CUAV®. It uses a higher-performance STM32H7 processor and integrates industrial-grade sensors and ultra-low temperature drift sensors. Compared with the previous flight controller,it has better performance and more reliability. This board can run ArduPilot firmware perfectly. X7+ Pro is ideal for industrial drones.

X7

[!TIP] X7+ Pro autopilot is a derivative version of X7 Pro. From January 1, 2022, X7+ Pro will replace X7 Pro; X7+ Pro is perfectly compatible with ArduPilot 4.10/PX4 V1.12.3 and higher firmware.X7+ Pro supports monitoring Servo port voltage, the maximum input voltage of Servo port is 10V; other parts have no difference.

Other characteristics

  • High-precision industrial sensor(ADIS16470+RM3100+ICM42688-P)
  • A new generation of CUAV patented shock absorption, better shock absorption effect
  • 3 sets of IMU sensors,supporting intelligent failover
  • Support IMU heating, make the sensor work better
  • Modular design, can be DIY carrier board
  • Support more Dshot output
  • Dedicated UAVCAN power interface

Quick Summary

  • Main FMU Processor: STM32H743
  • On-board sensors:

    • Accelerometer/Gyroscope: ICM42688-P(X7 Pro:ICM-20649)
    • Accelerometer/Gyroscope: ADIS16470
    • Accelerometer/Gyroscope: ICM20689-P(X7 Pro:BMI088)
    • Magnetometer: RM3100
    • Barometer: MS5611*2
  • Interfaces:

    • 14 PWM outputs (12 supports Dshot)
    • Support multiple RC inputs (SBUs/PPM/DSM)
    • Analogue / PWM RSSI input
    • 2 GPS ports(GPS and UART4 ports)
    • 4 i2c buses(Two i2c dedicated ports)
    • 2 CAN bus ports
    • 2 Power ports(Power A is common adc interface, Power C is uavcan battery interface)
    • 2 ADC intput
    • 1 USB ports
  • Power System:
    • Power: 4.5~5.4V
    • USB Input: 4.75~5.25V
    • Servo Rail Input: 0~10V
  • Weight and Dimensions:
    • Weight: 101g
  • Other Characteristics:
    • Operating temperature: -20 ~ 85°c
    • Three imus
    • Supports temperature compensation
    • Internal shock absorption

Purchase

CUAV Store

Size and Pinouts

X7+ pro pinouts

x7+ pro pinouts

[!Warning] The RCIN port is limited to powering the rc receiver and cannot be connected to any power/load.

Voltage Ratings

  • Nora AutoPilot can be triple-redundant on the power supply if three power sources are supplied. The two power rails are: Power A, Power C and *USB.

[!NOTE] The output power rails PWM OUT (0V to 10V) do not power the flight controller board (and are not powered by it). You must supply power to one of Power A, Power C or USB or the board will be unpowered.

Normal Operation Maximum Ratings

Under these conditions all power sources will be used in this order to power the system:

  1. POWERA and POWERC inputs (4.5V to 5.4V)
  2. USB input (4.75V to 5.25V)

Building ArduPilot Firmware

./waf configure --board CUAV-x7

./waf copter --upload

Debug Port

The system's serial console and SWD interface operate on the DSU7 port. Simply connect the FTDI cable to the DSU7 connector (the product list contains the CUAV FTDI cable).

Peripherals

  • Digital Airspeed Sensor
  • Telemetry Radio
  • Rangefinders/Distance sensors
  • others

Further info

results matching ""

    No results matching ""