C-RTK2 Quick start

This section introduces how to quickly configure and use C-RTK 2.

Build an aerial survey system

According to your different needs, you need to prepare the following equipment first

Only use PPK

PPK base station/Ntrip account *1
C-RTK 2 *1
Mapping camera *1
Drone *1

PPK+RTK

PPK base station/Ntrip account *1
C-RTK 2 *1
Mapping camera *1
Drone *1
Data link *1
Computer *1

[!NOTE] C-RTK 2 is used as an RTK base station and rover station, as well as a PPK rover station,It is not recommended to be used as a PPK base station.

Hardware connection

According to different camera types, there are different connection methods

Five-lens mapping camera/DIY method

Use can cable to connect flight controller and C-RTK2 (communication and power supply)
Use the hot shoe cable to connect to the hot shoe cable of the five-lens camera
The shutter trigger pin of the flight control is connected to the five-lens camera shutter cable

Canon/Sony cameras and other cameras with hotshoes

Use can cable to connect flight controller and C-RTK2 (communication and power supply)
Use the hotshoe cable to connect to the hotshoe PCB and C-RTK Hotshoe interface, and insert the PCB into the camera hot shoe interface
The shutter trigger pin of the flight control is connected to the Shutter in interface
C-RTK2 Shutter out is connected to the camera shutter interface

[!NOTE] The above is the recommended method of use. You can also use it with a camera without hot shoe feedback and use the shutter trigger to record the POS; but you may need to tolerate the accuracy error caused by the delay.

Camera without hot shoe (shutter trigger recording pos)

[!NOTE] For some special cameras without hot shoe feedback, C-RTTK supports the use of shutter trigger to record POS; but due to various reasons, there is an error (delay) between the camera and POS recording time; it may affect the accuracy of aerial survey; when using this method The C-RTK 2 parameter CAM_FEEDBACK_TYPE needs to be set to 0.

Use the can cable to connect the flight controller and the CAN (communication and power supply) of the C-RTK2.
The shutter trigger pin of the flight controller is connected to the Shutter in interface
C-RTK2 Shutter out is connected to the camera shutter port

Install to drone

[!NOTE] The direction of the device should be consistent with the direction of the aircraft; otherwise, you may need to configure additional flight control parameters

[!NOTE] It is recommended to install the C-RTK2 antenna directly above the camera to avoid configuring the antenna offset.

Set flight control parameters

Depending on the flight controller firmware, the set parameters are different. The following is the setting guide for ArduPilot/PX4 firmware. If you use other flight controllers, please refer to the relevant controller shutter setting guide; the following configuration uses common relay/level shutter Trigger as an example; also supports PWM shutter trigger.

ArduPilot

[!NOTE] The flight control parameters are set in MissionPlanner》Configuration》All parameter table/parameter tree. After modification, please click the write button on the right side and restart the flight control.

Enable UAVCAN

[!NOTE] The following settings are to enable UAVCAN to provide RTK/navigation data for the flight controller; if you only use C-RTK 2 as a PPK, you do not need to perform this operation.

CAN_D1_PROTOCOL =1
CAN_P1_DRIVER =1(Enable CAN1）
CAN_D2_PROTOCOL =1**
CAN_P2_DRIVER =1**(Enable CAN1）
GPS_TYPE =9 Or GPS1_TYPE= 9(AP4.6.0 and later versions)

Set the flight control camera shutter output

* `CAM_TRIGG_TYPE`=1（0=PWM，1=ralay）
* `CAM_RELAY_ON`=0（0=low，1=high）
* `CAM_MIN_INTERVAL`=0（The shortest shutter interval time, unit: milliseconds, 1000=1 second）
* `CAM_MAX_ROLL`=0（If the tilt exceeds this angle, the time-lapse shooting will not trigger until the angle returns to normal, 0=no limit）
* `CAM_AUTO_ONLY`=0（When to on the shutter, 0=anytime, 1=only in AUTO mode）
* `Relay_pin`=55（Ralay pin；The flight controller without io should be set to 63）

For AP4.6 and above version firmware

CAM1_TYPE=1（1=PWM，2=ralay）<br/>
CAM1_RELAY_ON=0（0=low，1=high）<br/>
CAM1_MIN_INTERVAL=0（The shortest shutter interval time, unit: milliseconds, 1000=1 second）<br/>
CAM1_MAX_ROLL=0（If the tilt exceeds this angle, the delayed shooting will not be triggered until the angle returns to normal, 0=no limit) CAM_AUTO_ONLY=0 (when the shutter can be triggered, 0=any time, 1=only in AUTO mode<br/>
Relay_pin=55（Ralay pin；The flight controller without io should be set to 63）<br/>
CAM1_FEEDBAK_PIN=54(Ralay pin；The flight controller without io should be set to 62）<br/>
CAM1_FEEDBAK_POL=1（0=low，1=high）<br/>

Test shutter trigger

Use the remote control to control the shutter:
RC?_OPTION=9(?=?=Remote control channel, for example, RC7_OPTION=9, then the remote control channel 7 is dialed to the high position to take pictures).
Ground station instructions:

In the action bar of the flight data of the ground station, select Trigger_camera and click to execute the action to trigger the camera.

PX4

[!NOTE] The flight control parameters are set in QGroundcontrol》parameters. After modification, please click the ok button on the right and restart the flight control.